Difference between revisions of "S1 Pro+ Sub EQ"
(Created page with "{{DivToc |RightHead = Sub EQ |RightBody = The Sub EQ setting is a crossover that optimizes system EQ for setup scenarios in which a powered subwoofer is connected to the sys...") |
m |
||
| (4 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
| + | {{Sub icon}}{{S1 Pro+ icon}} | ||
{{DivToc | {{DivToc | ||
| Line 5: | Line 6: | ||
|RightBody = The Sub EQ setting is a crossover that optimizes system EQ for setup scenarios in which a powered subwoofer is connected to the system LINE OUT port. | |RightBody = The Sub EQ setting is a crossover that optimizes system EQ for setup scenarios in which a powered subwoofer is connected to the system LINE OUT port. | ||
| − | You can use Sub EQ with any powered subwoofer, but for optimal performance, Bose recommends the Bose | + | You can use Sub EQ with any powered subwoofer, but for optimal performance, Bose recommends the Bose Sub1 or Sub2 Powered Bass Module. |
Once you enable Sub EQ, it stays enabled until you disable it or the system powers off. | Once you enable Sub EQ, it stays enabled until you disable it or the system powers off. | ||
| + | With the Sub EQ mode you can use the {{S1 Pro+}} internal mixer as the sound source (e.g., microphone and guitar and backing tracks via Bluetooth). This is different from the {{S1 Pro}} where the preferred method was to route all sound sources to the Sub1/Sub2 first and from the Sub1/Sub2 to the {{S1 Pro}}. This is because the {{S1 Pro}} did not have the Sub EQ mode. | ||
| + | |||
| + | ;Sub EQ, Dual Wireless Streaming, Livestream Mode | ||
| + | |||
| + | <html> | ||
| + | <iframe width="560" height="315" src="https://www.youtube.com/embed/pZ_EeecttPA?si=vgSGN1IYxNAWf55i" title="YouTube video player" frameborder="0" allow="accelerometer; autoplay; clipboard-write; encrypted-media; gyroscope; picture-in-picture; web-share" referrerpolicy="strict-origin-when-cross-origin" allowfullscreen></iframe> | ||
| + | </html> | ||
| Line 17: | Line 25: | ||
}} | }} | ||
| + | {{S1 Pro+ with Sub1 or Sub2}} | ||
Latest revision as of 10:53, 1 August 2024
Sub EQ
The Sub EQ setting is a crossover that optimizes system EQ for setup scenarios in which a powered subwoofer is connected to the system LINE OUT port.
You can use Sub EQ with any powered subwoofer, but for optimal performance, Bose recommends the Bose Sub1 or Sub2 Powered Bass Module.
Once you enable Sub EQ, it stays enabled until you disable it or the system powers off.
With the Sub EQ mode you can use the S1 Pro+ internal mixer as the sound source (e.g., microphone and guitar and backing tracks via Bluetooth). This is different from the S1 Pro system where the preferred method was to route all sound sources to the Sub1/Sub2 first and from the Sub1/Sub2 to the S1 Pro system. This is because the S1 Pro system did not have the Sub EQ mode.
- Sub EQ, Dual Wireless Streaming, Livestream Mode
Using Inputs on S1 Pro+
You can use the S1 Pro+ as the sound source (e.g., microphone and guitar and backing tracks via Bluetooth). This is different from the S1 Pro system where the preferred method was to route all sound sources to the Sub1/Sub2 first and from the Sub1/Sub2 to the S1 Pro system. This is because the S1 Pro system did not have the Sub EQ mode.
Engage the S1 Pro+ Sub EQ and use the S1 Pro+ Line Out to send a full range signal to the Sub1/Sub2.
- Note these settings on the S1 Pro+
- 👉 Turn on the Sub EQ (see the excerpt from the manual below)
- Note these settings on the Sub1 or Sub2
- 👉 Set LINE IN EQ to L1
- 👉 Set LINE OUT EQ to S1 (Press and hold LINE OUT EQ button for 4 seconds)
Note the following:
- On the S1 Pro+ turn on the Sub EQ setting. This sets the internal high pass filter to approximately 150 Hz.
- The Sub EQ setting does not affect the S1 Pro+ Line Out. The Line Out remains full-range
- With the Sub EQ turned on, the S1 Pro+ will produce frequencies above 150 Hz and you will be able to push S1 Pro+ harder (louder) without low-end distortion
- Without the Sub EQ turned on, the S1 Pro+ will sound the same as without the subwoofer
- The Sub1 or Sub2 will cover from 40 Hz (Sub1) 37 Hz (Sub2) to 150 Hz
Connection with a Mixer (optional)
Connections with Sub1 or Sub2 and the S1 Pro system
Using a mixer, the signal flow goes from
- The signal source (e.g., ToneMatch Mixer[1], mixer, DJ console) output to
- The Sub1 or Sub2 subwoofer LINE IN 1 to
- The Sub1 or Sub2 subwoofer LINE OUT 1 to
- The S1 Pro+ channel 3 Aux with level 10 o'clock.
- Note these settings on the Sub1 or Sub2
- 👉 Set LINE IN EQ to L1
- 👉 Set LINE OUT EQ to S1 (Press and hold LINE OUT EQ button for 4 seconds)
Set up this way,
- The Sub1 or Sub2 handles frequencies from 40 Hz (Sub1) 37 Hz (Sub2) to 150 Hz
- The S1 Pro system handles frequencies above 150 Hz
