Difference between revisions of "Template:S1 Pro B1 Compatibility"
m (→Using a Bose B1 with the S1 Pro or S1 Pro+) |
m (→Using a Bose B1 with the S1 Pro or S1 Pro+) |
||
| Line 1: | Line 1: | ||
| + | {{S1 Pro icon}}{{S1 Pro+ icon}}{{B1 icon}}{{B2 icon}} | ||
== Using a Bose B1 with the S1 Pro or S1 Pro+ == | == Using a Bose B1 with the S1 Pro or S1 Pro+ == | ||
| Line 10: | Line 11: | ||
<summary></html><big>Technical Notes</big><html></summary></html> | <summary></html><big>Technical Notes</big><html></summary></html> | ||
| − | The B1 Bass Module is a band‑pass enclosure optimized for use with L1 systems. When connected to an L1 Model I/II/1S, the internal DSP in the power stand generates a dedicated bass signal for the B1. This processing: | + | The B1 Bass Module is a band‑pass enclosure optimized for use with L1 systems. When connected to an L1 Classic/Model I/II/1S, the internal Digital Signal Processor (DSP) in the power stand generates a dedicated bass signal for the B1. This processing: |
* Restricts the B1 to its intended operating range (approximately 40–200 Hz) | * Restricts the B1 to its intended operating range (approximately 40–200 Hz) | ||
| Line 17: | Line 18: | ||
* Routes the processed signal to a dedicated 250 W @ 4 Ω amplifier (internal or PackLite A1) | * Routes the processed signal to a dedicated 250 W @ 4 Ω amplifier (internal or PackLite A1) | ||
| − | + | TheDSP topology has not been published, but the result is a controlled band‑pass feed that keeps the B1 operating safely and musically. | |
The S1 Pro and S1 Pro+ do not provide this processing. Their XLR Line Out is full‑range and unprocessed. | The S1 Pro and S1 Pro+ do not provide this processing. Their XLR Line Out is full‑range and unprocessed. | ||
| Line 30: | Line 31: | ||
Without this processing, the B1 will not perform as intended and may be at risk of low‑frequency over‑excursion if driven hard. | Without this processing, the B1 will not perform as intended and may be at risk of low‑frequency over‑excursion if driven hard. | ||
| − | For bass reinforcement with the S1 Pro or S1 Pro+, the Bose Sub1 is the recommended solution. It includes internal DSP, limiting, crossover management, and a built‑in 480 W amplifier, and accepts a full‑range line‑level signal directly from the S1 Pro/S1 Pro+. | + | For bass reinforcement with the S1 Pro or S1 Pro+, the Bose Sub1/Sub2 is the recommended solution. It includes internal DSP, limiting, crossover management, and a built‑in 480 W amplifier, and accepts a full‑range line‑level signal directly from the S1 Pro/S1 Pro+. |
<html></details></html> | <html></details></html> | ||
| Line 39: | Line 40: | ||
! Feature | ! Feature | ||
! Bose B1 | ! Bose B1 | ||
| − | ! Bose Sub1 | + | ! Bose Sub1/Sub2 |
|- | |- | ||
| Intended system | | Intended system | ||
| L1 Model I/II/1S | | L1 Model I/II/1S | ||
| − | | S1 Pro, S1 Pro+, L1 Pro systems | + | | S1 Pro, S1 Pro+, L1 Pro systems, Legacy L1 systems |
|- | |- | ||
| Required processing | | Required processing | ||
Revision as of 14:39, 11 February 2026
Using a Bose B1 with the S1 Pro or S1 Pro+
The Bose B1 Bass Module was designed for the L1 family of systems, not the S1 Pro or S1 Pro+. The S1 Pro+ provides a full‑range line output, while the B1 requires a dedicated low‑frequency signal and a matched amplifier to operate correctly.
To use a B1 with an S1 Pro or S1 Pro+, you would need extra equipment such as a crossover, a separate power amplifier, and additional cabling. This adds cost and complexity, and the results may not match what the B1 delivers when used with an L1 system.
For simple, reliable bass reinforcement, the Bose Sub1 is the recommended companion for the S1 Pro and S1 Pro+. It connects directly, includes the correct crossover and protection, and provides deeper, more powerful bass with no extra gear required.
Technical Notes
The B1 Bass Module is a band‑pass enclosure optimized for use with L1 systems. When connected to an L1 Classic/Model I/II/1S, the internal Digital Signal Processor (DSP) in the power stand generates a dedicated bass signal for the B1. This processing:
- Restricts the B1 to its intended operating range (approximately 40–200 Hz)
- Shapes the response using a B1‑specific EQ curve
- Applies limiting matched to the B1’s mechanical and thermal capabilities
- Routes the processed signal to a dedicated 250 W @ 4 Ω amplifier (internal or PackLite A1)
TheDSP topology has not been published, but the result is a controlled band‑pass feed that keeps the B1 operating safely and musically.
The S1 Pro and S1 Pro+ do not provide this processing. Their XLR Line Out is full‑range and unprocessed.
To operate a B1 correctly behind an S1 Pro or S1 Pro+, an external signal chain is required:
- A crossover or DSP to create a 40–200 Hz band‑limited signal for the B1
- Level control to balance the B1 with the S1 Pro/S1 Pro+
- An external power amplifier capable of approximately 250 W @ 4 Ω
- Appropriate cabling (XLR/TRS to DSP, DSP to amplifier, Speakon to B1)
Without this processing, the B1 will not perform as intended and may be at risk of low‑frequency over‑excursion if driven hard.
For bass reinforcement with the S1 Pro or S1 Pro+, the Bose Sub1/Sub2 is the recommended solution. It includes internal DSP, limiting, crossover management, and a built‑in 480 W amplifier, and accepts a full‑range line‑level signal directly from the S1 Pro/S1 Pro+.
Comparison: B1 vs Sub1 with the S1 Pro/S1 Pro+
| Feature | Bose B1 | Bose Sub1/Sub2 |
|---|---|---|
| Intended system | L1 Model I/II/1S | S1 Pro, S1 Pro+, L1 Pro systems, Legacy L1 systems |
| Required processing | Needs external DSP to create 40–200 Hz band‑pass | Built‑in DSP, crossover, limiting |
| Required amplification | External amp (~250 W @ 4 Ω) | Built‑in 480 W Class‑D amplifier |
| Connection to S1 Pro/S1 Pro+ | Requires DSP + amp + cabling | Direct line‑level connection |
| Low‑frequency extension | Limited (band‑pass design) | Deeper, fuller bass |
| Maximum output | Modest | Significantly higher |
| Ease of setup | Complex | Simple, plug‑and‑play |