Difference between revisions of "Kemper Player Airstep"
(Created page with " These are the settings on the Airstep to make it mimic the behaviour of the Kemper rig buttons one through five {| class="wikitable" ! Switch Name !! Toggle Mode !! LED Disp...") |
m |
||
| Line 25: | Line 25: | ||
| || || || Release || CC || 54 || 0 || ALL || 1 | | || || || Release || CC || 54 || 0 || ALL || 1 | ||
|} | |} | ||
| + | |||
| + | == Summary of Kemper MIDI Logic (Slots + Morph) == | ||
| + | * '''CC#50–54''': Load Slots 1–5 in Performance Mode or Rigs 1–5 in Browser Mode. | ||
| + | * '''Morph Triggering''': If the same CC is sent again (with value 1–127), Morph is engaged. | ||
| + | * '''Morph Release''': Sending value 0 disengages Morph. | ||
| + | * '''Momentary vs Latching''': Controlled by the Rig’s internal “Momentary” setting. | ||
| + | |||
| + | == Why Your Airstep Setup Works == | ||
| + | * '''Press''' = CC#50–54 value 1 → Loads Rig or Slot | ||
| + | * '''Release''' = CC#50–54 value 0 → Ends Morph (if Momentary is enabled) | ||
| + | * '''Repeated Presses''' → Toggle Morph (if Momentary is disabled) | ||
| + | * '''Single Button Logic''' → Matches Kemper Stage/Remote behavior exactly | ||
Revision as of 15:14, 15 September 2025
These are the settings on the Airstep to make it mimic the behaviour of the Kemper rig buttons one through five
| Switch Name | Toggle Mode | LED Display | Trigger | MIDI Type | CC# | Value | Output Interface | MIDI Channel |
|---|---|---|---|---|---|---|---|---|
| KPA 1 | Off | Normal Mode | Press | CC | 50 | 1 | ALL | 1 |
| Release | CC | 50 | 0 | ALL | 1 | |||
| KPA 2 | Off | Normal Mode | Press | CC | 51 | 1 | ALL | 1 |
| Release | CC | 51 | 0 | ALL | 1 | |||
| KPA 3 | Off | Normal Mode | Press | CC | 52 | 1 | ALL | 1 |
| Release | CC | 52 | 0 | ALL | 1 | |||
| KPA 4 | Off | Normal Mode | Press | CC | 53 | 1 | ALL | 1 |
| Release | CC | 53 | 0 | ALL | 1 | |||
| KPA 5 | Off | Normal Mode | Press | CC | 54 | 1 | ALL | 1 |
| Release | CC | 54 | 0 | ALL | 1 |
Summary of Kemper MIDI Logic (Slots + Morph)
- CC#50–54: Load Slots 1–5 in Performance Mode or Rigs 1–5 in Browser Mode.
- Morph Triggering: If the same CC is sent again (with value 1–127), Morph is engaged.
- Morph Release: Sending value 0 disengages Morph.
- Momentary vs Latching: Controlled by the Rig’s internal “Momentary” setting.
Why Your Airstep Setup Works
- Press = CC#50–54 value 1 → Loads Rig or Slot
- Release = CC#50–54 value 0 → Ends Morph (if Momentary is enabled)
- Repeated Presses → Toggle Morph (if Momentary is disabled)
- Single Button Logic → Matches Kemper Stage/Remote behavior exactly