Difference between revisions of "External Subwoofers"
m (tightened text) |
m (→Third Party (non-{{Bose}}) Systems) |
||
| (9 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
| − | |||
=== Passive (unpowered) Loudspeakers === | === Passive (unpowered) Loudspeakers === | ||
| − | Using loudspeakers other than the {{B1}} with any of the {{L1}} systems is not supported. However you can safely try your own external subs if the impedance is no lower then 4 ohms (typically a single 4 ohm loudspeaker or two 8 ohm loudspeakers in parallel). The output from the Power Stand is 250 watts RMS into 4 ohms. | + | {{Classic icon}}{{Model I icon}}{{Model II icon}} |
| + | Using loudspeakers other than the {{B1}} with any of the {{L1 nl}} systems is not supported. However you can safely try your own external subs if the impedance is no lower then 4 ohms (typically a single 4 ohm loudspeaker or two 8 ohm loudspeakers in parallel). The output from the Power Stand is 250 watts RMS into 4 ohms. | ||
==== {{Classic nl}} and {{Model I nl}}==== | ==== {{Classic nl}} and {{Model I nl}}==== | ||
| − | {{ | + | {{Classic icon}}{{Model I icon}} |
| + | For the sake of those attaching third party passive speakers (an unsupported application). | ||
| + | |||
| + | Output if no {{B1}}s detected | ||
| + | * 40-{{{Crossover|180}}} Hz Bandpass (that is: NO B1 EQ) | ||
| + | |||
| + | If one or two {{B1}}s detected (or resistors used across NL4 2+ / 2- pins to emulate detection) | ||
| + | * 40-{{{Crossover|180}}} Hz with different EQ curves. For details on how to do this see: [[Activating B1 EQ Curves]] | ||
| + | |||
| + | For more details about the Power Stand outputs see: [[PS1 Power Stand / Bass Line Out]] | ||
==== {{Model II nl}}==== | ==== {{Model II nl}}==== | ||
| − | {{ | + | {{Model II icon}} |
| + | For the sake of those attaching third party passive speakers (an unsupported application). | ||
| + | |||
| + | Output if no {{B1}}s detected | ||
| + | * 40-{{{Crossover|200}}} Hz Bandpass (that is: NO B1 EQ) | ||
| + | |||
| + | If one or two {{B1}}s detected (or resistors used across NL4 2+ / 2- pins to emulate detection) | ||
| + | * 40-{{{Crossover|200}}} Hz with different EQ curves. For details on how to do this see: [[Activating B1 EQ Curves]] | ||
| + | |||
| + | For more details about the Power Stand outputs see: [[L1® Model II Power Stand / Bass Line Out]] | ||
=== Active (powered) Loudspeakers=== | === Active (powered) Loudspeakers=== | ||
| − | Using powered loudspeakers with any of the {{L1 nl}} systems is not supported. The [[PackLite® power amplifier Model A1]] is part the {{l1 nl}} System. It can be used to power up to two {{B1}}s. This is connected to the Power Stand Bass Line Out | + | {{Classic icon}}{{Model I icon}}{{Model II icon}} |
| + | Using powered loudspeakers with any of the {{L1 nl}} systems is not supported. | ||
| + | |||
| + | ==== [[PackLite® power amplifier Model A1]] ==== | ||
| + | The [[PackLite® power amplifier Model A1]] is part the {{l1 nl}} System. It can be used to power up to two {{B1}}s. This is connected to the Power Stand Bass Line Out. | ||
| + | ==== Third Party (non-{{Bose}}) Systems ==== | ||
If you want to use a powered loudspeaker system, you can use the Power Stand Bass Line Out as the signal source. Here are notes specific to the {{L1 nl}} you are using. | If you want to use a powered loudspeaker system, you can use the Power Stand Bass Line Out as the signal source. Here are notes specific to the {{L1 nl}} you are using. | ||
| Line 22: | Line 45: | ||
Please see [[PackLite® power amplifier Model A1]] for extensive notes that include ideas that can be applied to other systems. | Please see [[PackLite® power amplifier Model A1]] for extensive notes that include ideas that can be applied to other systems. | ||
| + | |||
| + | == Ongoing discussion == | ||
| + | [http://bose.infopop.cc/eve/forums/a/tpc/f/3976055944/m/178108737 I need more bass article - discussion] | ||
| + | |||
| + | ---- | ||
| + | [[Category:Bass]] | ||
| + | [[Category:Unsupported Applications]] | ||
Latest revision as of 15:22, 21 September 2010
Contents
Passive (unpowered) Loudspeakers
Using loudspeakers other than the B1 Bass Module with any of the L1® systems is not supported. However you can safely try your own external subs if the impedance is no lower then 4 ohms (typically a single 4 ohm loudspeaker or two 8 ohm loudspeakers in parallel). The output from the Power Stand is 250 watts RMS into 4 ohms.
L1® Classic and L1® Model I
For the sake of those attaching third party passive speakers (an unsupported application).
Output if no B1 Bass Modules detected
- 40-180 Hz Bandpass (that is: NO B1 EQ)
If one or two B1 Bass Modules detected (or resistors used across NL4 2+ / 2- pins to emulate detection)
- 40-180 Hz with different EQ curves. For details on how to do this see: Activating B1 EQ Curves
For more details about the Power Stand outputs see: PS1 Power Stand / Bass Line Out
L1® Model II
For the sake of those attaching third party passive speakers (an unsupported application).
Output if no B1 Bass Modules detected
- 40-200 Hz Bandpass (that is: NO B1 EQ)
If one or two B1 Bass Modules detected (or resistors used across NL4 2+ / 2- pins to emulate detection)
- 40-200 Hz with different EQ curves. For details on how to do this see: Activating B1 EQ Curves
For more details about the Power Stand outputs see: L1® Model II Power Stand / Bass Line Out
Active (powered) Loudspeakers
Using powered loudspeakers with any of the L1® systems is not supported.
PackLite® power amplifier Model A1
The PackLite® power amplifier Model A1 is part the L1® System. It can be used to power up to two B1 Bass Modules. This is connected to the Power Stand Bass Line Out.
Third Party (non-Bose®) Systems
If you want to use a powered loudspeaker system, you can use the Power Stand Bass Line Out as the signal source. Here are notes specific to the L1® you are using.
You will probably use an powered loudspeaker in the same way as you would connect an PackLite® amp.
Please see PackLite® power amplifier Model A1 for extensive notes that include ideas that can be applied to other systems.
Ongoing discussion
I need more bass article - discussion