Difference between revisions of "S1 Pro as Monitor with Third Party Mixer and L1"
m |
m (Text replacement - "Category:S1" to "Category:S1 Pro") |
||
| (6 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
| − | {{Model II}}{{S1 icon}} | + | {{Model II icon}}{{S1 icon}} |
| + | <div class="tocdiv"> | ||
| + | <div>__TOC__</div> | ||
| + | <div><h2>Summary</h2> | ||
| + | This is an overview of how you can connect a third party mixer to an L1 as the main output and {{S1}} as a monitor. | ||
| + | </div> | ||
| + | </div> | ||
| − | == | + | === Example === |
| − | + | You can connect using the XLR outputs from a mixer. | |
| + | This assumes you are running mono and have all mixer inputs panned up the middle. | ||
| + | |||
| + | ==== XLR Outputs ==== | ||
[[File:Yamaha MG10XU L1 S1 XLR.jpg|400px]] | [[File:Yamaha MG10XU L1 S1 XLR.jpg|400px]] | ||
| + | You can connect using the {{1/4 TRS}} outputs from a mixer. | ||
| + | ==== {{1/4 TRS}} Outputs ==== | ||
[[File:Yamaha MG10XU L1 S1 TRS.jpg|400px]] | [[File:Yamaha MG10XU L1 S1 TRS.jpg|400px]] | ||
| + | |||
| + | |||
| + | ==== XLR and {{1/4 TRS}} Outputs ==== | ||
| + | If your mixer has both XLR and {{1/4 TRS}} outputs, you can pan all inputs to one side (e.g., Left) and connect like this. | ||
[[File:Yamaha MG10XU L1 S1 14 XLR trs.jpg|400px]] | [[File:Yamaha MG10XU L1 S1 14 XLR trs.jpg|400px]] | ||
| + | |||
| + | ==== {{S1}} Settings ==== | ||
| + | |||
| + | Set the controls on the {{S1}} like this. | ||
[[File:S1 Pro Settings for mixer.jpg|250px|S1 Pro inputs]] | [[File:S1 Pro Settings for mixer.jpg|250px|S1 Pro inputs]] | ||
| − | + | <!-- | |
==Cables== | ==Cables== | ||
[[File:14trstotrs.jpg|200px|right|{{1/4 TRS}}]] | [[File:14trstotrs.jpg|200px|right|{{1/4 TRS}}]] | ||
:The {{T1}} Analog Outputs and the {{S1}} 1/4 inch (6.3 mm) inputs are '''balanced'''. For best results use a {{1/4 TRS}} cable for a balanced connection. You can use a {{1/4 TS}} , but you will lose up to -6 dB in signal strength and you may pick up line noise. | :The {{T1}} Analog Outputs and the {{S1}} 1/4 inch (6.3 mm) inputs are '''balanced'''. For best results use a {{1/4 TRS}} cable for a balanced connection. You can use a {{1/4 TS}} , but you will lose up to -6 dB in signal strength and you may pick up line noise. | ||
| − | + | --> | |
=={{S1}} settings== | =={{S1}} settings== | ||
On the {{S1}} use these settings while you are setting up. | On the {{S1}} use these settings while you are setting up. | ||
| Line 32: | Line 51: | ||
For each channel you are using on the S1 Pro System, | For each channel you are using on the S1 Pro System, | ||
# Turn the channel volume off | # Turn the channel volume off | ||
| − | # Connect the {{ | + | # Connect the mixer output to the {{S1}} |
| − | # Set the | + | # Set the mixer to the maximum you will use during your performance. |
# While playing/singing as loud as you will during your performance, bring up the {{S1}} channel volume until you see solid green on the channel indicator light. Occasional flickers of red are okay. If you see solid red or you hear distortion, turn down the volume. | # While playing/singing as loud as you will during your performance, bring up the {{S1}} channel volume until you see solid green on the channel indicator light. Occasional flickers of red are okay. If you see solid red or you hear distortion, turn down the volume. | ||
| Line 39: | Line 58: | ||
---- | ---- | ||
[[Category:Mixer]] | [[Category:Mixer]] | ||
| − | [[Category:S1]] | + | [[Category:S1 Pro]] |
[[Category:Model II]] | [[Category:Model II]] | ||
[[Category:Model 1S]] | [[Category:Model 1S]] | ||
Latest revision as of 22:23, 16 November 2019
Summary
This is an overview of how you can connect a third party mixer to an L1 as the main output and S1 Pro System as a monitor.
Example
You can connect using the XLR outputs from a mixer.
This assumes you are running mono and have all mixer inputs panned up the middle.
XLR Outputs
You can connect using the 1/4 inch (6.35 mm) Tip-Ring-Sleeve outputs from a mixer.
1/4 inch (6.35 mm) Tip-Ring-Sleeve Outputs
XLR and 1/4 inch (6.35 mm) Tip-Ring-Sleeve Outputs
If your mixer has both XLR and 1/4 inch (6.35 mm) Tip-Ring-Sleeve outputs, you can pan all inputs to one side (e.g., Left) and connect like this.
S1 Pro System Settings
Set the controls on the S1 Pro System like this.
S1 Pro System settings
On the S1 Pro System use these settings while you are setting up.
- Reverb OFF
- Bass at 12:00 o'clock
- Treble at 12:00 o'clock
- ToneMatch switch OFF
You can adjust the Reverb, Bass, and Treble after you get your basic sound working.
S1 Pro System Gain Staging
For each channel you are using on the S1 Pro System,
- Turn the channel volume off
- Connect the mixer output to the S1 Pro System
- Set the mixer to the maximum you will use during your performance.
- While playing/singing as loud as you will during your performance, bring up the S1 Pro System channel volume until you see solid green on the channel indicator light. Occasional flickers of red are okay. If you see solid red or you hear distortion, turn down the volume.