T1 ToneMatch Audio Engine Master Out to S1 Pro system

From Bose Portable PA Encyclopedia
(Redirected from T1 to L1 and S1)
Jump to: navigation, search

To use your S1 Pro System as a monitor for your T1 ToneMatch Audio Engine with L1 Model II or L1 Model 1S connect:

T1 Master with Model II to S1.jpg

T1 ToneMatch Audio Engine Master Out to an S1 Pro System

T1MasterOutput.png

The T1 ToneMatch Audio Engine Master Out is a 1/4 inch (6.3 mm) Tip-Ring-Sleeve balanced mono output and it is suitable to connect to the S1 Pro System Channel 1 or 2.

For best results use a 1/4 inch (6.3 mm) Tip-Ring-Sleeve cable. A 1/4 inch (6 mm) Tip-Sleeve cable will have up to -6dB lower signal and be more susceptible to line noise.


Applicability
This article applies to connecting the T1 ToneMatch Audio Engine Master Output or Aux Output to the S1 Pro System

T1MasterOutput.png

T1AuxOutput.png

Power for the T1 ToneMatch Audio Engine
If your T1 ToneMatch Audio Engine is connected to an L1 Model 1S or L1 Model II, the T1 ToneMatch Audio Engine will get power from the Power Stand. If it not, you will need a ToneMatch Power Supply to run the T1 ToneMatch Audio Engine.
Cables
1/4 inch (6.35 mm) Tip-Ring-Sleeve
The T1 ToneMatch Audio Engine Analog Outputs and the S1 Pro System 1/4 inch (6.3 mm) inputs are balanced. For best results use a 1/4 inch (6.35 mm) Tip-Ring-Sleeve cable for a balanced connection. You can use a 1/4 inch (6.35 mm) Tip-Sleeve cable, but you will lose up to -6 dB in signal strength and you may pick up line noise.




On the S1 Pro System, for each channel you are connecting to the T1 ToneMatch Audio Engine use these settings while you are setting up.

S1 Pro Settings for mixer.jpg

  • Reverb OFF
  • Bass at 12:00 o'clock
  • Treble at 12:00 o'clock
  • ToneMatch switch OFF

You can adjust the Reverb, Bass, and Treble after you get your basic sound working.

S1 Pro+

You can also connect to the Channel 3 Aux input. For best results, use a 1/4 inch (6.3 mm) Tip-Ring-Sleeve cable.

S1 Pro+ Channel 3 Inputs.jpg



Gain Staging

Using a Bose device as the source

When connecting a ToneMatch Mixer[1] or an S1 Pro System Line Out to an S1 Pro System channel 1 or channel 2

Set the volume control to 10:00 o'clock with 1/4 inch (6.3 mm) Tip-Ring-Sleeve

The signal strength from a ToneMatch Mixer[1] or an S1 Pro System Line Out is sufficient to achieve the maximum usable volume from the S1 Pro System
Control the overall volume from the ToneMatch Mixer[1] or the first S1 Pro System. If you use an XLR cable, set the volume control to 9:00 o'clock

ToneMatch Mixer to S1 Pro.jpg


Using a third-party source (not a Bose device as the source)

For each channel you are using on the S1 Pro System

  1. Turn the channel volume off
  2. Connect your sound source
  3. Adjust the volume of the source device output to the reference or nominal output level.
    • On analog consoles this may be marked as unity or 0 dB.
    • On digital consoles this may be marked as -18 dBFS[2][3]. The exact value (-18 dBFS to -20 dBFS) may vary depending your location[4].
    • Refer to the manual for the source device for details.
    • If the source device does not have metering or indicators, set the output as high as you can without hearing distortion or seeing red indicator lights.
  4. While playing/singing as loud as you will during your performance, bring up the channel volume until you see solid green on the channel indicator light. Occasional flickers of red are okay. If you see solid red or you hear distortion, turn down the volume.

Combo Inputs

S1 Pro Channels 1 and 2 have combo inputs that accept
  • XLR (balanced mono)
    • Microphone or Line-Level inputs
  • 1/4 inch (6.3 mm) Tip-Ring-Sleeve connection (balanced mono)
    • Line-Level inputs
  • 1/4 inch (6.3 mm) Tip-Sleeve connection (unbalanced mono)
    • Line-Level inputs and instruments (e.g. guitars, keyboards, guitar processors, loopers)
When using a third-party device (e.g., mixer or another line-level source) should I use the XLR or 1/4 inch inputs?
  • The S1 Pro 1/4 inch Tip-Ring-Sleeve inputs are best suited for line-level balanced inputs. This is a better match for the signal level.
  • The S1 Pro XLR inputs are best suited for microphones.

When the S1 Pro Channel input lights hit red or you hear distortion, the signal is clipping and you've reached the maximum usable volume. From the source, if the XLR outputs are line-level and the 1/4 inch Tip-Ring-Sleeve outputs are line-level, it won't matter which type of cable you use. They'll both get the job done, although the volume control setting will be lower with the XLR connection. That doesn't indicate more headroom. The maximum usable volume is the same either way.




Alternate Connection

You can use an XLR cable (mic cable) from a Line Level Source (e.g., L1 Pro, S1 Pro+) to S1 Pro or S1 Pro+ channels 1 or 2 (XLR inputs), but the signal may clip, overload, or be too high to control the volume. To attenuate (reduce) the signal, use a -20 dB or -30 dB Pad

XLR Cable

XLR cable.jpg

Pad

More about Pads

Click image for more information about Pads

Connecting a Mixer to an S1 Pro system

Article from Bose Connecting an S1 Pro to a mixer



[[Category:S1}}

For more details about the T1 settings please see: T1 ToneMatch® Audio Engine / Aux