T4S/T8S ToneMatch® Mixer

Introduced January 23, 2018

Documentation

T4S/T8S ToneMatch® Mixer Owner's Guide

T4S/T8S Quick Start Guide

T4S T8S ToneMatch Mixer Service Manual

Firmware update instructions

Firmware Updates

Turn the Rotary Selector to Prefs.

Turn the left-most button (Menu) to Versions.

Press the left-most button to select Versions to see the current firmware version

The latest version for the T4S/T4S/T8S Firmware is version 1.2.3 (Released for customer download August,2024)

Update for Firmware version 1.2.3 released August 2024

Download the file that is appropriate to your operating system. If you download these, you have all the files you need to do the update process: ToneMatch Updater software, instructions, and the Firmware file (*.bos)

Windows

ToneMatch Updater for Windows with firmware version 1.2.3
Contains updater and firmware *.bos files for both T4S and T8S

OR

Mac

ToneMatch Updater for Mac with firmware version 1.2.3
Contains updater and firmware *.bos files for both T4S and T8S

If you have trouble with the file above on your Mac,

1. Download the ToneMatch Updater Program first.
2. Download T4ST8S123.zip - the firmware only (*.bos) files for the T4S and T8S. Extract these to the same folder as you have the ToneMatch Updater program.
3. Run the ToneMatch Updater Program.

Note

Performing the firmware update will reset the USB A playback level all the way down (Mute)

---

If you need to update your firmware see:

T4S T8S Firmware Update Instructions

---

USB A Playback

Attach a USB Type-A flash drive to play any WAV/MP3 files stored to the flash drive.

Using the menu, select the folder that contains the WAV/MP3 files; select the file you want to play and adjust the level by rotating the Level control.

---

Attach a USB Type-A flash drive to play any WAV/MP3 files stored to the flash drive.

Turn the Rotary Selector to Prefs, then in the Menu select USB A Playback

Using the menu, select the folder that contains the WAV/MP3 files; select the file you want to play, and adjust the level by rotating the Level control.

Note

Routing settings for USB from PC are also applied to USB A playback. See USB B from PC below

USB drives Bose has tested with the T4S and T8S ToneMatch mixers

• Verbatim Nano 8GB - USB 2.0 (49820)
• Toshiba TransMemory 32GB U303 - USB 3.0 (THN-U303W0320E4)
• SanDisk Cruzer Blade 64GB - USB 2.0 (SDCZ50-064G-B35)
• SanDisk Cruzer Blade 32GB - USB 2.0 (SDCZ50-032G)
• SanDisk Ultra Flair 16GB - USB 3.0 (SDCZ73-016G-G46)
• Intenso Alu Line 16GB - USB 2.0 (specific model # unclear)
• PNY 64GB - USB 2.0 (FD64GATT4-EF)
• Kingston DataTraveler 50 32GB - USB 3.1 (specific model # unclear)
• PNY Attache 16GB - USB 2.0 (FD16GATT03-GE)

---

The following devices have been reported to work by T4S/T8S owners.

Sandisk Extreme 64Gb formatted FAT 32

Notes

• Some customers have reported that you can only have 64 files in a folder. More than 64 will not be recognized.
• If you have .wav files that won't play, try converting them to .mp3 files.

---

USB B from PC

Documentation Update

USB B from PC can be directed to:

• None
• Aux In
• Channel 3 or 4 (T4S) ⇐ New
• Channel 7 or 8 (T4S) ⇐ New
• Master

USB B from PC to Aux

If you have questions or comments on this video please see this discussion in the Bose Pro Portable PA Community

USB B from PC to Channels

If you have questions or comments on this video please see this discussion in the Bose Pro Portable PA Community

Aux Inputs

The T4S (5/6) and T8S (9/10) Aux Inputs, are routed directly to the Master Output buss.

We cannot route them to different channels or Aux outputs. You can control Pan and Level sent through to Master.

There's no other processing available (e.g. Presets, EQ, Effects).

Aux Outputs

T4S/T8S

This is an overview of using the Aux Outputs on the T4S and T8S ToneMatch® mixers. You can use the Aux outputs for monitors, remote speakers, or recording.

The steps are the same for the T8S and T4S.

T4S

Setting up monitors example

Connect your monitors to the T8S Aux Outputs. On the T8S you have four Aux Outputs. You can direct any channel to one of the Aux Outputs to create a monitor mix. As you assign a channel to an Aux Output, you can set the level and make the Aux send from the channel:

Dry : After Preamp

The only control that has an effect on the signal is the channel trim.

Pre : With EQ and FX

All settings for Preset, zEQ, ParaEQ, effects are sent through to the Aux output. The volume is controlled by the Level setting in this menu. Volume is not affected by the channel volume control. Reverb available for Aux 1 output only.

Post : After Fader

Same as Pre (above) except the volume is controlled by the channel volume control.

Select a Channel you want to direct to one of the Aux outputs. In the image below the Channel 1 CH Edit button is selected.

Turn the Rotary Selector to PAN/AUX

Turn the left most button under the display Menu to see your options. You can choose Pan, Aux Input, or one of the Aux Outputs

This is how it looks on the T8S when you turn the menu far enough to see all four Aux Outputs. On the T4S there are two Aux Outputs.

In this picture, we have chosen to direct Channel 1 to Aux 1. The level is 50% and the Tap is set to Pre

In this picture, Aux 1 is selected and you can choose if you want the Tap point to be Dry, Pre, or Post

Please see T8S Aux Send Channel Inputs to Different Aux Outputs for a detailed example.

Reverb on Aux 1

There are two reverb systems in the T4S/T8S ToneMatch® Mixers

1. Main reverb for channels 1 through 4 (T4S) and 1 through 8 (T8S)
   1. Turn Rotary Selector to Global/Reverb Type
   2. Menu: Main (that's the default)
   3. Set the Type, Time, and Balance
   4. For each individual channel (CH EDIT Button)
      • Turn Rotary Selector to Reverb
      • Menu: Main (that's the default)
      • Set Mix, Bright
2. Aux 1 Reverb
   1. Turn Rotary Selector to Global/Reverb Type
   2. Menu: Aux 1 (you have to turn the Menu button to see it)
   3. Set the Type, Time, and Balance
   4. For each individual channel (CH EDIT Button)
      • Turn Rotary Selector to Reverb
      • Menu: Aux 1 (you have to turn the Menu button to see it)
      • Set Mix, Bright

---

No Reverb on Aux 2(,3,4)

Question

Why is there no Reverb on the Aux 2, 3, 4 output of the T8S?

Answer

The T8S mixer has lots of different effects units and normally they are unique to each channel. That means that the T8S mixer has 4 individual dynamic processors, 4 modulators (chorus flanger, phaser, tremolo), 4 EQs, 4 parametric EQs, 4 delay processors. The only exception is the reverb, which is shared by all channels.

The output of the shared reverb processor contains the reverb portions of all 8 channels. If we send that to an Aux output, you'd hear the reverb portions of all 8 channels and not only the channel that you are interested in. In most cases, this is probably not what you want. That is why we cannot use the main reverb processor for the Aux Outputs.

Aux is also a per-channel control. That means if you turn up Aux 1 send the of a channel, you expect to hear signals from channel 1 and only from channel 1. This thinking applies to each of the channels and aux sends.

We have a separate reverb processor for Aux 1. If you use it, you hear reverb in Aux 1, and only Aux 1.

If we shared Aux 1 reverb with the other Aux channels, you would hear the reverb from all the Aux channels in every Aux output. That is why there is no reverb on Aux 2, 3, 4 output of the T8S

Workaround

Try using Digital Delay instead of Reverb for your vocals.

Digital Delay

Time: 100 ms

Mix: 15% - vary up to 30%

Fdbk: 0% - vary up to 10%

You should have better intelligibility and move the vocals out in front of the backing tracks.

Unlike Reverb, Digital Delay processing can be routed to ToneMatch Mixer Aux outputs.

---

---

---

Scenes

Documentation Update

The following is a correction of the T4S/T8S ToneMatch Mixer Owners Guide

The T4S/T8S includes three types of scenes:

• (5) Bose scenes: Factory-preset scenes. You can edit and overwrite them.
• (6) User Scenes: User-definable scenes for saving and recalling all your favorite settings. You can update these scenes by overwriting them as many times as you want.
• Coming soon - One of the User Scenes will be converted to a Shared Scene: A user-definable scene for saving settings you want to share with other T4S/T8S ToneMatch® mixer users. This scene can be uploaded to a computer using the L1® updater software available

Mono Output

T4S ToneMatch® mixer

Pan all inputs hard RIGHT

Connect your L1® to the RIGHT ToneMatch® port

OR

Use the ¼ inch (6mm) Right Output to a powered loudspeaker (e.g. S1 Pro, L1® Compact, F1 Model 812). For best results use a ¼ inch (6mm) jack Tip-Ring-Sleeve cable.

T8S ToneMatch® mixer

Pan all inputs hard RIGHT

Use the ¼ inch (6mm) Right Output to a powered loudspeaker (e.g. S1 Pro, L1® Compact, F1 Model 812). For best results use a ¼ inch (6mm) jack Tip-Ring-Sleeve cable

OR

Use the XLR Right Output to powered a loudspeaker (e.g. S1 Pro, F1 Model 812). or L1® Compact with XLR to ¼ inch (6mm) jack Tip-Ring-Sleeve.

T4S to S1 Pro

T4S

S1 Pro  

Connect a T4S ToneMatch mixer to an S1 Pro System as the only powered loudspeaker

Note

To use the T4S ToneMatch mixer with an S1 Pro System you need a ToneMatch Power Supply unless you are also connected to an L1 Model 1S or L1 Model II.

Connect a T4S ToneMatch mixer to an S1 Pro System as a Monitor

If you are using the S1 Pro System as monitor while using an L1 or L1 Pro as the main system, you can connect as shown in the rest of this article OR create a separate monitor mix using the T4S Aux Outputs. Everything else in this article is still applicable. For more details see: T4S Aux Outputs

Mono

Stereo

If you have questions please join the conversation in the Bose Portable PA Community

Connections

1. Leave the T4S and S1 Pro turned off until you have things connected
2. Connect the T4S power supply to the T4S (T4S power supply sold separately)
3. Connect the T4S Right Output to S1 Pro channel 1 or 2

Recommended cable

Use a 1/4 inch (6.35 mm) Tip-Ring-Sleeve cable for best results.

You can use and 1/4 inch (6.35 mm) Tip-Ring-Sleeve to XLR cable, but you will have to turn down the volume on the S1 Pro System to avoid clipping the input.

T4S Settings

1. Set the Rotary Selector to PAN/AUX
2. Press the CH EDIT button for each channel you are using and pan the input hard RIGHT
   Note: Steps 1 and 2 above are one-time-only. You don't have to change this unless you get another S1 Pro and want to run in stereo
3. Connect all your sound sources to the T4S
   • Turn on those sound sources that have power switches
4. Turn off the T4S Master Volume
5. If any of your sound sources require phantom power, press the T4S phantom power button
6. Turn on the T4S
7. Turn on the S1 Pro
8. Bring up the channel volume on the S1 Pro to about 11:00 o'clock
9. Control the volume using the T4S Master Volume

If you see the S1 Pro channel 1 light turning solid red occasionally, turn down the volume on the T4S
Or if you see the S1 Pro channel 1 light turning solid red frequently, turn down the volume on the S1 Pro

S1 Pro Settings

1. Turn off the reverb
2. Set both tone controls to the center position
3. Set the channel volume off
4. Turn on the T4S

On the S1 Pro System, for each channel you are connecting to the T4S/T8S ToneMatch® Mixer use these settings while you are setting up.

• Reverb OFF
• Bass at 12:00 o'clock
• Treble at 12:00 o'clock
• ToneMatch switch OFF

You can adjust the Reverb, Bass, and Treble after you get your basic sound working.

S1 Pro+

You can also connect to the Channel 3 Aux input. For best results, use a 1/4 inch (6.3 mm) Tip-Ring-Sleeve cable.

Gain Staging

Using a Bose device as the source

When connecting a ToneMatch Mixer or an S1 Pro System Line Out to an S1 Pro System channel 1 or channel 2

Set the volume control to 10:00 o'clock with 1/4 inch (6.3 mm) Tip-Ring-Sleeve

The signal strength from a ToneMatch Mixer or an S1 Pro System Line Out is sufficient to achieve the maximum usable volume from the S1 Pro System

Control the overall volume from the ToneMatch Mixer or the first S1 Pro System. If you use an XLR cable, set the volume control to 9:00 o'clock

---

Using a third-party source (not a Bose device as the source)

For each channel you are using on the S1 Pro System

1. Turn the channel volume off
2. Connect your sound source
3. Adjust the volume of the source device output to the reference or nominal output level.
   • On analog consoles this may be marked as unity or 0 dB.
   • On digital consoles this may be marked as -18 dBFS. The exact value (-18 dBFS to -20 dBFS) may vary depending your location.
   • Refer to the manual for the source device for details.
   • If the source device does not have metering or indicators, set the output as high as you can without hearing distortion or seeing red indicator lights.
4. While playing/singing as loud as you will during your performance, bring up the channel volume until you see solid green on the channel indicator light. Occasional flickers of red are okay. If you see solid red or you hear distortion, turn down the volume.

---

Combo Inputs

S1 Pro Channels 1 and 2 have combo inputs that accept

• XLR (balanced mono)
  • Microphone or Line-Level inputs
• 1/4 inch (6.3 mm) Tip-Ring-Sleeve connection (balanced mono)
  • Line-Level inputs
• 1/4 inch (6.3 mm) Tip-Sleeve connection (unbalanced mono)
  • Line-Level inputs and instruments (e.g. guitars, keyboards, guitar processors, loopers)

When using a third-party device (e.g., mixer or another line-level source) should I use the XLR or 1/4 inch inputs?

• The S1 Pro 1/4 inch Tip-Ring-Sleeve inputs are best suited for line-level balanced inputs. This is a better match for the signal level.
• The S1 Pro XLR inputs are best suited for microphones.

When the S1 Pro Channel input lights hit red or you hear distortion, the signal is clipping and you've reached the maximum usable volume. From the source, if the XLR outputs are line-level and the 1/4 inch Tip-Ring-Sleeve outputs are line-level, it won't matter which type of cable you use. They'll both get the job done, although the volume control setting will be lower with the XLR connection. That doesn't indicate more headroom. The maximum usable volume is the same either way.

Alternate Connection

You can use an XLR cable (mic cable) from a Line Level Source (e.g., L1 Pro, S1 Pro+) to S1 Pro or S1 Pro+ channels 1 or 2 (XLR inputs), but the signal may clip, overload, or be too high to control the volume. To attenuate (reduce) the signal, use a -20 dB or -30 dB Pad

XLR Cable

Pad

Click image for more information about Pads

Connecting a Mixer to an S1 Pro system

Article from Bose Connecting an S1 Pro to a mixer

---

---

Headphone Output

1. The headphone output is on the right side of the ToneMatch mixer. It is compatible with stereo headphones using a 1/4 inch (6mm) tip-ring-sleeve, stereo jack.
2. On the face of the ToneMatch mixer, is the PHONES volume control. It is beside the headphone output. This controls the volume you hear in the headphones.
3. The headphone output is the same as the Main outputs (Left and Right) except the volume is controlled by the PHONES volume control instead of the MASTER volume.
4. The CH Mute buttons affect both the Main outputs and the headphone output. There is no independent preview/cue/solo function for the headphones independent of the Main outputs.

Reverb Settings

Adding Reverb to a Channel

The Reverb function applies a user-adjustable amount of reverb to the selected channel. To select the type of reverb, see “Selecting a Reverb Type” below. Note: To mute the Reverb effects, press the Mix control. Press it again to unmute.

1. Press or rotate the Menu control and select which output (Main of Aux) to send the reverb to.
2. Rotate the Mix control to adjust the desired mix of dry signal (0%) to wet signal (100%).
3. Rotate the Bright control to equalize the high frequencies of reverb applied to the selected channel

Setting Global Reverb Type

Selecting a Reverb Type

The Reverb Type function allows you to select the type of reverb that is applied to all input channels. The decay time (Time) and balance (Bal) are adjustable. Balance controls the ratio of early-to-late reflections.

Note: To mute the Reverb, press the Type control. Press it again to unmute.

Global Reverb Settings are different from the T1 ToneMatch Audio Engine.

T4S/T8S ToneMatch® Mixers Global Reverb settings
Menu	Main or Aux 1 (apply following settings to Main or Aux)
Type	Plate, Small, Medium, Large, Cavern
Time	Expressed as a percentage of the time range for each reverb type Reverb Type         Time Range Plate 0 – 4.6 s Small 0 – 0.8 s Medium 0 – 1.9 s Large 0 – 3.5 s Cavern 0 – 7.0 s
Balance	Percentage (ratio of early/later reflections)
Selecting a type of reverb On the T4S or T8S, select if you are applying the reverb type to the Main output or Aux output Select Reverb Type with the rotary selector. Press the Type button to display the list of reverbs: Plate Creates the ambience of a typical studio plate reverb. Features adjustable time and balance (ratio of early/later reflections) parameters. Works well with guitars, horns, percussion instruments, and vocals. Small Creates the ambience of a small-sized space. Features adjustable time and balance (ratio of early/later reflections) parameters. Works well with guitars, horns, percussion instruments, and vocals. Medium Creates the ambience of a medium-sized space. Features adjustable time and balance (ratio of early/later reflections) parameters. Works well with guitars, horns, percussion instruments, and vocals. Large Creates the ambience of a large-sized space. Features adjustable time and balance (ratio of early/later reflections) parameters. Works well with guitars, horns, percussion instruments, and vocals. Cavern Creates the ambience of an extremely large space. Features adjustable time and balance (ratio of early/later reflections) parameters. A unique and interesting reverb effect. Rotate the Type button to scroll through the reverb list and highlight the desired reverb type. Press the Type button to select. (T4S/T8S only) Press the Balance button to select the Time Control Rotating the Time control controls the decay time of the selected reverb model from its minimum decay time to its maximum decay time. At 0%, the decay time will be at minimum and will simulate the smallest room size available to the currently selected reverb type. At 100%, the decay time will be at maximum and will simulate the largest room size available to the currently selected reverb type. Each reverb type has their own usable range of decay times that work best for the selected model type. The Reverb Decay parameter allows you to adjust the reverb time between the specific ranges that work best for the selected reverb model type. (T4S/T8S only) Press the Time control to switch to Bal. Rotate the Bal. control to adjust the early-to-late reflection ratio (0% = all early reflections, 100% = all late reflections).

Note

The Time settings are different from the T1 ToneMatch Audio Engine. There are no direct mappings of the time values in the T1 to the T4S/T8S because they use different units of measure.
If you are trying to get the same results as you had with a T1 ToneMatch^® Audio Engine make sure you have Firmware version 1.1.4 or later. Fine tune the settings by ear.

T1 ToneMatch Audio Engine Global Reverb settings
Type	Plate, Small, Medium, Large, Cavern
Time	Milliseconds from 0.20 - 9.79 seconds
Balance	Percentage (ratio of early/later reflections)

---

T8S no ToneMatch port connection to L1®

Bose engineered all the ToneMatch mixers (T1®, T4S, T8S) to offer the same excellent quality audio whether you use the ToneMatch cable (T1® or T8S) or a balanced cable (T8S) for audio.

If you are using good quality balanced cables there should be no difference between using any combination of XLR and 1/4 inch Tip-Ring-Sleeve connections.

The benefit of using the Cat-5 cable for the T1® or T4S is convenience because you don't need to use the T1®/T8S power supply. Unfortunately, the Model II Power Stand can not supply enough power to operate a T8S.

T8S Analog Outputs

The outputs on the T8S are analog. The RJ45 port is for the ToneMatch Power Supply that is included with the T8S. The RJ45 port cannot be used to connect to an L1® Model II or L1® Model 1S.

Bose engineered all the ToneMatch mixers (T1®, T4S, T8S) to offer the same excellent quality audio whether you use the ToneMatch cable (T1®, T4S) or a balanced cable for audio (T8S).

There are two balanced 1/4 inch (6mm) Tip-Ring-Sleeve outputs (Left and Right). These are convenient for connecting to the L1® Model II or L1 Model 1S Power Stands as well as F1 Model 812s.

There are two balanced XLR outputs (Left and Right). These are convenient for connecting to other powered loudspeakers with XLR inputs.

Total number of inputs - Comparing T8S with two T1®s

With the T8S and two L1® Model 1S or L1® Model II you have

• 8 - Combo inputs
• 2 - Aux inputs 1/4 inch (6mm)

That's 10 inputs in total.

With the T1® with two L1® Model II or L1® Model 1S

First T1®

• 3 - Combo inputs
• 1 - Aux input 1/4 inch (6mm). Channel 4/5 is a single channel with two inputs.
• 1 - Aux input on the L1® Model 1S or L1 Model II Power Stand

Second T1®

• 3 - Combo inputs
• 1 - Aux input 1/4 inch (6mm). Channel 4/5 is a single channel with two inputs.
• 1 - Aux input on the L1® Model 1S or L1 Model II Power Stand

The total is

• 6 - Combo inputs
• 4 Aux inputs 1/4 inch (6mm)

That's 10 inputs in total. If you want to count Channel 5 on the T1®s you're up to 12 inputs, but channel 4/5 is really a single channel with two input jacks for combining a stereo signal.

Comparison to T1® ToneMatch audio engine

Note

The T4S/T8S ToneMatch® Mixers are compatible with the L1 Pro Systems (announced October 2020).

The T1 ToneMatch Audio Engine requires two connections to the L1 Pro Systems: one for power, one for audio. Please see: T1 Compatibility With L1 Pro Systems

Here's a quick rundown of the additions and changes

• Stereo outputs and processing
  • T4S: Two digital ToneMatch outputs and parallel analog 1/4" Tip-Ring-Sleeve
  • T8S: Two XLR analog outputs two analog 1/4" Tip-Ring-Sleeve
  • Pan

• Combo inputs
  • T4S: Channels 1, 2, 3 and 4 all have combo XLR-1/4" inputs
  • T8S: Channels 1, 2, 3, 4, 5, 6, 7 and 8 all have combo XLR-1/4" inputs
• Auxilliary inputs (routed to Main with Level and Pan controls)
  • T4S: Aux Channels 5 and 6 are 1/4" Tip-Ring-Sleeve
  • T8S: Aux Channel 9 and 10 that are 1/4" Tip-Ring-Sleeve
• Headphone jack
• 6mm (1/4"-20) threaded insert at the bottom for use with mounting hardware,
• Tap-tempo delay
• Aux Outputs
  • Dedicated Reverb on Aux 1
    • T4S: Additional Aux out - Aux 2
    • T8S: Additional Aux outs - Aux 2 Aux 3, Aux 4
• 3-band Parametric EQ per channel
• Master out 6-band EQ
• Higher signal output (approximately +10 dB) and this provides greater compatibility with the F1 Model 812 Flexible Array Loudspeaker
• USB playback (WAV/MP3) from thumb drives
• New industrial design
• New magnetic cover

Removed/Changed

• Removed the L1® Cylindrical Radiator® stand and the mic stand adapter (replaced by the common 1/4"-20 insert)
• Removed the preamp outs based on customer feedback that they were seldom used
• There are eleven scenes available in the T4S/T8S ToneMatch® Mixers:

Five Bose Scenes (that can be overwritten) and

Six user scenes

The T1® has eleven user read/writeable Scenes and five Bose read only Scenes.

T1 Scenes backed up to a computer can not be restored to a T4S/T8S (different architecture for reverb)

• New Reverb engine
  • Global Reverb Time parameter is expressed in percentage compared to the T1® in seconds (details)
• Channel 4 (T4S compared to T1)

T4S ToneMatch Mixer	T1 ToneMatch Audio Engine
Channel 4 Combo 1/4" (6.3mm) / XLR input. This single input is mono and can be panned. XLR input Phantom Power Support for bare piezo pickups (pickups without a preamp) Full support for ToneMatch Presets, zEQ, ParaEQ, Effects, Reverb Can be routed to Aux Outputs 1 and/or 2	Channel 4 A single mono channel with two 1/4" (6.3mm) balanced line-level inputs that were immediately converted to mono. No XLR input No phantom power No support for bare piezo pickups (pickups without a preamp) Full support for ToneMatch Presets, zEQ, ParaEQ, Effects, Reverb Can be routed to Aux Output 1
Aux Inputs Channels 5/6 Two 1/4" (6.3mm) balanced line-level inputs Each input can be panned Left or Right Each input is routed directly to the Master Outputs No processing (ToneMatch Presets, zEQ, ParaEQ, Effects, Reverb) Cannot be routed to Aux 1 or 2 Each input level control is set using the Prefs | PAN/AUX settings	No equivalent

---

T4S/T8S ToneMatch Mixer FAQs

What is the T4S/T8S ToneMatch Mixer?

Take control of your music with T4S and T8S ToneMatch mixers, compact 4 and 8 channel interfaces designed for performers. Engineered with powerful DSP engines and intuitive user controls, they offer studio-quality EQ, dynamics and effects processing. Sound great with integrated Bose® ToneMatch processing and zEQ, especially when connected to a Bose L1 or F1 system for full end-to-end tonal control. Play confidently on stage with these rugged ToneMatch mixers using tactile controls, easy-to-read LED displays and scene recall. ToneMatch mixers, the ultimate on-stage companions for performing artists.

What are the key features of the T4S/T8S ToneMatch mixers?

Powerful Audio Processing
Elevate your performances with updated, studio-quality effects and advanced digital audio processing. Never run out of options with channel-independent EQ, dynamics and effects. Get your perfect sound fast with Bose ToneMatch processing for natural-sounding vocals and instruments, while zEQ focuses your tone for effective adjustments on the fly. When used with Bose L1 and F1 systems, the T4S/T8S mixers allows full end-to-end optimization of your sound.

Seamless Live Control
The T4S/T8S integrates with your performance using illuminated, tactile controls and indicators for spontaneous sound adjustments, even on dimly-lit stages. Jump into settings with the fast-learning, intuitive control interface. Additional features like tap tempo delay, built-in chromatic tuner, master out EQ, and recallable scenes makes it easy to be ready to play. The T4S/T8S is the ultimate on-stage companion for performing artists.

High-Density Connectivity
For it’s size, the stereo T4S/T8S mixer gives you unprecedented connectivity with control. Four (T4S) or eight (T8S) main channels feature high-quality audio preamps with XLR-combo jacks for microphones or instruments, and switchable phantom power. Additionally, the T4S/T8S offers two (T4S) and four (T8S) Aux sends, two Aux inputs, two ToneMatch outputs for digital audio with remote power (T4S), USB-A and -B for USB drive playback or PC/Mac interfacing, a dedicated headphone jack, and ¼” TRS analog outputs.

Convenient Gig-Ready Features
Rugged and ready to go, the T4S/T8S includes a protective magnetic cover and a bottom insert allows you to use standard mounting accessories to keep the T4S/T8S within reach.

What are the differences between the T4S and the T8S?

The T4S and the T8S both have the same compact interface, tactile knobs and advanced digital audio processing, yet the T8S gives you an expanded channel count with four more mic/line inputs and a total of four Aux sends. The T8S also includes an output meter to visually monitor your output level. The T4S can receive power and send digital audio to L1 Model II or L1 Model 1S products when using the included ToneMatch cable. The T8S comes standard with a universal power supply and does not offer a ToneMatch link.

What are ToneMatch presets, and what are their benefits?

ToneMatch presets are designed for specific instruments and microphones for use with the L1 Model 1S/II system, S1 Pro or F1 system. ToneMatch presets are available for each channel and instantly bring you closer to the true sound of your voice or instrument – all at the touch of a button. When you select a proprietary ToneMatch preset for your microphone or instrument, you are tapping into a powerful technology, available only from Bose.

What is the concept behind zEQ, and what are the benefits?

Ordinary tone controls are generic by design: “High,” “Mid” and “Low” controls are spread out across the entire musical spectrum. Proprietary zEQ automatically shifts the range of these controls so that they correspond directly to the range of your voice or instrument. zEQ gives you more precise control over your tone, making it easy to fine-tune your sound.

What is the benefit of the ToneMatch ports on the T4S?

When used with ToneMatch cables, connect the outputs of the T4S to one or two L1 Model 1S/II units via their ToneMatch ports. The user may enjoy the benefits of digital quality audio while alleviating the need for an additional power supply and excessive wiring when used with the L1 Model 1S/II system. (Note: this is for the T4S only, the T8S must be used with a power supply, although the T4S can be powered using the accessory ToneMatch power supply when not being used with an L1 system.)

What is the proper method for setting the gain on the T4S/T8S ToneMatch mixer?

Adjust the output volume of the source instrument to normal operating volume, or sing into the microphone using your loudest level. Make sure that the Master volume and the channel volume on the T4S/T8S are set to 0. While playing your instrument/audio sources as loudly as you would during a performance, turn the Trim control on applicable channel of the T4S/T8S clockwise until the signal/clip indicator glows green. If the indicator flashes red or glows steady red, turn the trim control counterclockwise to decrease the level until it’s most always green.

What are the two Aux outs on the T4S and 4 Aux outs on the T8S?

These are direct output signals that can be taken pre or post mix and connected to a number of different devices including personal monitors, amplifiers or recording devices. Aux outputs accept ¼” TRS balanced cables.

17" 18" 18

How many inputs does the T4S/T8S ToneMatch mixer have, and what type are they?

18"17"

Inputs 1-4 (1-8 with the T8S) are analog inputs channels with a combination input connector. This connector supports either balanced XLR audio cables or ¼” balanced (TRS) or unbalanced (TS) cables. Easily connect multiple sources with the added flexibility of accepting either balanced XLR audio cables or ¼” balanced or unbalanced cables.

Aux input channels 5&6 (9&10 T8S only) accept a ¼” balanced or unbalanced cable. Both inputs are independent of each other and can have separate volumes and pans. These stereo inputs are useful for connecting the outputs from PC audio interfaces, mixing consoles and keyboards/synths.

How can you verify the version of ToneMatch presets that are on the T4S/T8S?

Access the global preferences menu to confirm which interchangeable ToneMatch preset banks are loaded on the system. Use the rotary encoder to select the global Prefs mode. Press Menu button to select menu list, then rotate the Select button to scroll through the list and highlight the ToneMatch description.

What is the process for updating the T4S/T8S with new ToneMatch presets?

The T4S/T8S is equipped with a USB interface that may be connected to a PC. Check www.Bose.com/musicians for periodic updates on preset availability.

What is a Bose scene?

The T4S/T8S contains five Bose scenes each, which have specific default processing configurations for various applications intended as a starting point in achieving great sound. The T4S Bose scenes are Singer/songwriter, DJ/playback, Drums and bass, Electric works and Factory settings. The T8S Bose scenes are Full Band, String Band, Stereo DJ, Electronic and Factory settings.

T4S:

Bose Scene 01 – Singer/songwriter
Bose Scene 02 is designed for singer/songwriter playing keyboard or guitar and sometimes accompanied by an MP3 track.

Bose Scene 02 – DJ/playback
Bose Scene 03 is designed for a DJ event or any audio playback need. This setup uses two microphones and either an MP3 player, mixer or laptop PC.

Bose Scene 03 – Drums and bass
Bose Scene 04 is set up for a bass guitar, kick drum, and either an MP3 player or laptop PC.
Bose Scene 04 – Electric works
Bose Scene 05 is designed for electric and acoustic guitars, bass guitar and keyboard.

Bose Scene 05 – Factory settings
This scene restores the T4 mixer to the settings it had when it left the factory. Loading this scene erases any changes you previously made.

T8S

Bose Scene 01 – Full Band
Bose Scene 01 is designed for a full trio band with drums, bass, guitar and three vocal mics. This setup also uses aux 9/10 for backing tracks or set break music.

Bose Scene 02 – String Band
Bose Scene 02 is designed for a string band with a hand drum, bass, guitars, mandolin and vocal mics.

Bose Scene 03 – Stereo DJ
Bose Scene 03 is designed for a DJ to run multiple sources in a stereo configuration. It also has four vocal mics for any MC’s or announcements.

Bose Scene 04 – Electronic
Bose Scene 04 is designed for an electronic band. It has stereo source input, two stereo keyboard inputs and two vocal mics.

Bose Scene 05 – Factory Reset
This scene restores the T8S mixer to the settings it had when it left the factory. Loading this scene erases any changes you previously made.
 

What is a user-defined scene?

The T4S/T8S allows the user to easily store, recall and edit performance scenes (a snapshot of the complete state of the unit) into five user-defined scenes. User-defined scenes help achieve consistent sound with minimal configuration. After editing a Bose scene to your preference, you may re-save it as a user-defined scene, allowing you to easily recall it later. This greatly reduces the amount of configuration required.

What is a shared scene?

A shared scene is a single user scene that you can send out of the T4S/T8S to a PC when using the L1 updater software. This allows you to share the scene with other members of the user community. To obtain software, please go to www.Bose.com/musicians.

Does the T4S/T8S ToneMatch mixer have built-in effects? What are some of the features and applications where they may be used?

Yes. Below is a list of effects that users may independently assign/adjust for any or all channels. The user also enjoys discrete control over designated parameters for each respective channel.

Effects

Modulation

Chorus 1: Brite - Shimmering chorus that works well with acoustic instruments. Includes adjustable mix, depth and speed parameters.

Chorus 2: Warm - Like Chorus 1 but with slightly less high frequencies. Includes adjustable mix, depth and speed parameters and works well with electric guitars and basses.

Chorus 3: Dark - Like Chorus 2 but with less high frequencies for a darker tone. Includes adjustable mix, depth and speed parameters, and works well with electric guitars and basses.

Flanger 1: Tape - Tape-style flanger with no feedback. Includes adjustable mix, depth and speed parameters, and works well with electric guitars and basses.

Flanger 2: Feedback - Same as Flanger 1 but with preset Feedback effect.

Phaser 1: Stomp - Classic “stomp box”-style phaser. Features a preset wide speed with variable speed and feedback parameters, and works well with electric guitars/basses and keyboards.

Phaser 2: Rack - Classic “rack”-style phaser. Features a positive mix type with variable speed and feedback parameters, and works well on electric guitars/basses and keyboards.

Phaser 3: Warm - Vintage-style phaser. Features a positive mix type with variable speed and feedback parameters, and works well as an effect on electric guitars/basses and keyboards.

Phaser 4: Bright - Phaser with no bass. Features a positive mix type with variable speed and feedback parameters that works well on electric guitars and keyboards.

Tremolo - Vintage-style tremolo effect with variable speed and depth parameters that works well as an effect on guitars and keyboards.

Delay

Choose from analog, digital or tape delay. Independently assign/adjust the delay settings for desired channels with discrete control over the mix and feedback time parameters for each channel. For example, the user may select a tape delay for the vocal on Channel 1 while selecting an analog delay for the guitar on Channel 2. Set your delay time with the center knob or use the tap tempo feature by pressing the center knob at desired tempo.

Digital Delay - Digital delay effect where the repeats remain uncolored. Features adjustable mix, time, and feedback parameters, and may be used on guitars, drums or vocals.

Analog Delay - Classic analog delay effect, where the repeats continuously deteriorate. Features adjustable mix, time and feedback parameters, and may be used with guitars, drums or vocals.

Tape Delay - Vintage-style tape delay effect, where the repeats deteriorate even more than analog delay, and may be used with guitars, horns, harmonica or vocals.

Reverb
The T4S/T8S allows access to a global reverb type that may be applied to both the master output and Aux outputs, or you can select separate reverb types for the master outputs and Aux outputs. The reverb types are plate, small, medium, large and cavern. Control decay time and level of reverb signal sent through master output. Please keep in mind that once you select a global reverb type to be used among any or all channels, you may control the mix and brightness of each channel. However, the type of reverb may only be altered for all channels. This is achieved through adjusting the Reverb Type mixer mode.

Plate - Creates the ambience of a medium-sized space. Features adjustable time and balance (ratio of early/later reflections) parameters and may be used with guitar, horns, percussion instruments and vocals.

Small - Creates the ambience of a small-sized space. Features adjustable time and balance (ratio of early/later reflections) parameters and may be used with guitar, horns, percussion instruments and vocals.

Medium - Creates the ambience of a medium-sized space. Features adjustable time and balance (ratio of early/later reflections) parameters and may be used with guitar, horns, percussion instruments and vocals.

Large - Creates the ambience of a large-sized space. Features adjustable time and balance (ratio of early/later reflections) parameters, and may be used with guitar, horns, percussion instruments and vocals.

Cavern - Creates the ambience of an extremely large space. Features adjustable time and balance (ratio of early/later reflections) parameters, and may be used with guitar, horns, percussion instruments and vocals.

Dynamics Processing

Compressor 1: Light - Compressor featuring a preset low compression ratio with variable threshold and gain parameters. May be used as a general-purpose compression for most instruments and microphones that require minimal level control.

Compressor 2: Medium - Compressor featuring a preset moderate compression ratio with variable threshold and gain parameters and may be used with basses, guitars, keyboards, vocals or other instruments requiring subtle level control.

Compressor 3: Heavy - Compressor featuring a preset high compression ratio with variable threshold and gain parameters and may be used with loud instruments such as horns and drums, vocals or other instruments that require more aggressive level control.

Noise gate - adjustable threshold and speed independently assignable for each channel. Controls extraneous noise from open microphones or hot instrument pickups from being introduced into the system.

Limiter – User-adjustable threshold and gain settings are independently assignable for each channel.
Prevents input signals from overloading, helping to maintain consistent gain staging.

De-Esser – User-adjustable threshold and gain settings are independently assignable for each channel.
Compression useful in reducing high-end frequencies associated with vocal sibilant sounds.

Kick Gate - The Kick Gate is a Bose proprietary technology that allows you to drive your kick
drum to loud levels while avoiding microphone feedback.

Step 1: Connect an appropriate microphone. It is imperative that you gain
stage the microphone correctly. Your hardest kick hits should put the LED
clip meter solidly in the yellow, just shy of the red.

• Step 2: Activate the kick gate. Use the default settings initially. Turn the
volume of the system up to desired performance level.

• Step 3: Play the softest that you will play in the performance. You should
clearly hear these kick hits.

• Step 4: Playing softly, raise the
threshold knob until you hear some of your
kick hits get cut off. Back the threshold down 3db from this point.

• Step 5: Play the kick drum as you normally would. Reduce ‘Tightness’ to
add more boom to your sound.

• Step 6: Enjoy your kick drum!
 

Can you assign multiple effects to any or all channels?

Yes. The user may run multiple effects on one channel while simultaneously running a set of completely different effects on each of the other channels. Each effect type has designated user-adjustable parameters, which also may vary from channel to channel.

Can I create a sub mix to send to a house PA system or recording device?

Yes. The Aux outputs on the T4S/T8S allow you to send selected input channels to separate mixes by accessing the Aux menu under PAN/AUX. You then can determine if the signal will be Dry (after preamp), Pre (includes EQ and FX) or Post (after fader).

Does the T4S/T8S have amp modeling capability?

No. Distortion must be produced first and then fed into the T4S/T8S as a clean, non-clipping signal. To achieve distortion, the guitarist can use a few methods:

Inline devices: One popular method would be to use any of the effects pedals on the market or use a DSP-based amplifier modeler that models the tone produced by amplifier tubes, guitar transducers and guitar amplifier speaker cabinets.

Miking a guitar amplifier: Another method would be to use a guitar amplifier, and mic the speaker as closely as possible. The trick here is to run the amplifier at the lowest level at which the correct tone is attainable but does not diminish the benefits of the ToneMatch setting. Louder amplifiers can be located and miked offstage. Miking small, low-watt amplifiers is a better technique for this method.

Use a loading device: Some electric guitarists may prefer to use their amplifier's output as an input signal into the power stand. Before doing this, they must use a load device, such as a "Plate Soak" or a "Hot Plate" to give a line-level output suitable for the input stage of the T4S/T8S.

Use the "line output" of a guitar amplifier: Some amplifiers have this option, and it may be suitable for some guitarists. The only suggestion here is to turn the volume of the amplifier down so only the ToneMatch setting is heard.

Refer to the Bose website and Portable PA Community at www.Bose.com/musicians for more information on interfacing instruments with the ToneMatch mixers.

Can I purchase the T4S/T8S and use it with other Bose systems?

Yes. The T4S/T8S is available for purchase separately or may be used with an L1 Model 1S/II system, S1 Pro or F1 System. When the T4S/T8S is fused with one of the products, the ToneMatch settings are optimized for the loudspeaker. The T4S/T8S can be connected analog any number of amplifiers or loudspeakers. A power supply is required to run the mixer which is available through Bose or authorized dealers of Bose products.

What is the 45-day Better Music Guarantee?

At Bose, we recognize that customers may want to experience Bose portable PA components in their own environment with their specific gear. That is why we offer the ability for you to purchase and use the system in your specific application for up to 45 days. If for any reason you are not satisfied, you may return it for a refund. This offer is exclusive to Bose direct sales channels.

Where can you hear and try the T4S/T8S ToneMatch mixer?

40"39"

Order it and try it for 45 days, directly from Bose Corporation. We encourage customers to experience the T4S/T8S mixers in their own environment with their specific gear. That is why we offer the ability for you to purchase and use the system in your specific application for up to 45 days, and if for any reason you are not satisfied, you may return it for a refund. This offer is exclusive to Bose direct sales channels. Optionally, you can easily try out the product at participating MI retailers.

What is included with the purchase of the T4S/T8S ToneMatch mixers?

The T4S comes with a magnetic protective cover. The T4S comes also with a ToneMatch cable. T8S comes with both the magnetic protective cover and a universal power supply.

What are the available accessories for the T4S/T8S?

ToneMatch power supply
Comes standard with the T8S mixer, optional for the T4S mixer when used without a L1® Model 1S or L1 Model II system.

Carrying Case
A hard-shell briefcase with handle and available storage for cables for the T4S/T8S mixers.

Source: Bose Pro T4S/T8S FAQ

---