Search results

Create the page "Power" on this wiki! See also the search results found.

• Gain Staging
  ...&ck=0#question32 What is the proper method for setting the gain on the PS1 Power Stand?]</ref> ...gain. Set the trim for the individual channel at the back panel of the PS1 Power Stand. Supply a maximum source signal and watch the LED, when you start to
  7 KB (1,267 words) - 00:54, 30 November 2016
• Gain Staging/Chuck-at-Bose
  * Power Amp – A last big boost, by far the biggest of all, so big that it can mak === Full Power at 12:00 on Master Level ===
  7 KB (1,190 words) - 17:51, 29 December 2007
• Setup 5 Minutes
  * Power cable and if the player requires it for accessories, a small power bar ..." tape for labelling things (including the presets, gain settings, phantom power on/off normally used for each system). I'll probably get around to finding
  3 KB (524 words) - 00:28, 23 December 2008
• Spare Parts
  [[Image:T1PowerSupply.jpg|T1™ Power Supply]] ...eMatch™ audio engine when used with an L1™ Model I system or computer. Power rating: AC 100–120V~.
  2 KB (365 words) - 02:31, 13 January 2008
• DI
  ...circuitry and are known as active D.I. Boxes. They require either Phantom Power or a battery supply. ...and are known as either transformer or passive D.I. Boxes. They require no power supply.
  4 KB (608 words) - 15:46, 23 January 2013
• L1® Model I
  == PS1 Power Stand Input/Output Panel == {{PS1 Power Stand / What Do the LEDs Mean}}
  3 KB (425 words) - 15:59, 26 March 2017
• Downloads
  ...his is software in the physical device (e.g. S1 Pro, ToneMatch Mixer, L1® Power Stand).&nbsp;</p> === {{Model II nl}} Power Stand ===
  4 KB (647 words) - 22:00, 10 February 2020
• T1 ToneMatch® Audio Engine / Use without the L1® in Festival Situations
  * The T1 power switch should never be turned on or off while the T1 is connected to the "f * [[T1 ToneMatch® Audio Engine power supply]]
  5 KB (893 words) - 05:16, 26 March 2017
• Duo
  ...to an {{Model II}} then you will require the [[T1 ToneMatch® Audio Engine power supply]]. == {{Model II nl}}: Can I run a Stereo Source to the Model II Power Stand ==
  2 KB (345 words) - 11:58, 12 March 2010
• Using More Than Two B1s with a Power Stand
  <div style="float:right">{{#Click:PackLite® power amplifier Model A1|Image:PackliteExtendedBassPackage.png|114px|PackLite® e You can have up to two {{B1 nl}}s connected to an {{L1 nl}} Power Stand.
  945 bytes (157 words) - 13:46, 12 January 2009
• I Need More Bass
  ...great investment as this allows you to fully utilize the amplifier in the Power Stand that is dedicated to Bass. == More Than Two B1s with a Power Stand ==
  1 KB (237 words) - 23:45, 7 May 2019
• L1® Model II with Mixer to Analog Input
  ...{{T1}} use the mixer to create a mono output and send that to the Model II Power Stand Analog input. ...a stereo/mono switch then use it and send the mono output to the Model II Power Stand Analog input.
  2 KB (292 words) - 19:32, 30 September 2019
• Ethernet
  ...itter in conjunction with the T1 Tonematch Engine. Since that line carries power at specific voltage levels to the T1, splitting or combining these signals ; How do I connect a single {{T1 nl}} to two {{Model 1S}} Power Stands?
  1 KB (210 words) - 02:21, 19 March 2014
• TC-Helicon VoiceSolo FX150
  ...disadvantage is that you will not be hearing the mix that is going to the Power Stand (what the audience will hear). === Connecting Directly to a Power Stand ===
  6 KB (1,045 words) - 17:45, 30 April 2015
• T1 to T8S to Two L1 Model II
  === T1 Power === ...g the T1 to a power stand so you will need a [[T1 ToneMatch® Audio Engine power supply]].
  2 KB (290 words) - 12:39, 10 October 2019
• S1 Pro as Monitor with T1
  ==Power for the {{T1}}== ...ematch_powersupply_acc.html#v=l1_tonematch_powersupply_acc_black ToneMatch Power Supply] to run the {{T1}}.
  3 KB (433 words) - 22:23, 16 November 2019
• B2 instead of F1 Subwoofer
  Your B2 bass modules are passive (no built-in amplifier). The L1 Model II Power Stand provides # Power: 250 watts RMS
  1 KB (196 words) - 11:47, 5 March 2019
• ToneMatch Mixer Phantom Power to Tyros 5 Microphone Input
  ...it possible to connect and run the mic thru the input on Ch 1 with phantom power on the T1 tone match and run the out from ch1 to the keyboard would that wo #Turn on Phantom Power
  3 KB (474 words) - 13:59, 23 April 2019
• L1 Pro32 with Sub1 and L1 Pro16
  ...e an L1 Pro32 with Sub1, but not a Sub2. Instead, I connected an L1 Pro 16 power stand to the L1 Pro32 line out to simulate adding a Sub2. Then I cranked up ...ther Sub2, you can expect up to +6 dB SPL. You get +3 dB from doubling the power and up to +3 dB by doubling of acoustic volume, cone area and close couplin
  3 KB (508 words) - 23:20, 19 April 2021
• L1® Unofficial Users' Guide
  *[[PackLite® power amplifier Model A1|A1 PackLite® power amplifier Model A1]] *[[L1™ Model II Power Stand/Bass Line Out|Bass Line Out and B1s]]
  5 KB (637 words) - 02:54, 26 March 2017

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)