Difference between revisions of "Mixer / Mackie / ProFX8 and ProFX12"
m (New page: {{Classic icon}}{{Model I icon}} <big>'''Mackie DFX Mixer'''</big> == Summary == <table><tr><td> The simplest thing that could possibly work is to use the Mixer outputs shaded in Yellow....) |
m |
||
| (One intermediate revision by the same user not shown) | |||
| Line 5: | Line 5: | ||
<table><tr><td> | <table><tr><td> | ||
The simplest thing that could possibly work is to use the Mixer outputs shaded in Yellow. | The simplest thing that could possibly work is to use the Mixer outputs shaded in Yellow. | ||
| + | |||
| + | [[Image:MackieProFX8-12.jpg]] | ||
</td><td> | </td><td> | ||
| − | + | ||
</td> | </td> | ||
| Line 14: | Line 16: | ||
''' {{Use1/4}} ''' | ''' {{Use1/4}} ''' | ||
| + | == Outputs from the Mixer == | ||
| + | === ¼ Inch with suitable output=== | ||
| + | for PS1 Powerstand Channel 1 or 2 inputs | ||
| + | |||
| + | {{RunTROrTRSUnbalanced}} | ||
| − | |||
=== XLR Balanced +4 === | === XLR Balanced +4 === | ||
| − | |||
{{TooHotForPS1}} | {{TooHotForPS1}} | ||
| − | + | If you want to use XLR cables you may need to use a [[pad]] | |
| − | |||
| − | |||
| − | |||
| − | Links | + | == Links == |
* [http://www.mackie.com/products/profxseries/pdf/ProFX-OM.pdf Manual] | * [http://www.mackie.com/products/profxseries/pdf/ProFX-OM.pdf Manual] | ||
* [[Image:MackieProFX8-12.jpg]] | * [[Image:MackieProFX8-12.jpg]] | ||
Latest revision as of 14:34, 1 November 2010
Mackie DFX Mixer
Contents
Summary
|
The simplest thing that could possibly work is to use the Mixer outputs shaded in Yellow.
|
Use the ¼ inch phone jack (Tip-Sleeve) outputs to
- The PS1 Power Stand (Classic) / Model I Channels 1 or 2 if you want to use the Presets and the R1 Remote Tone and Level Controls
OR - The PS1 Power Stand (Classic) / Model I Channels 3 or 4 if you prefer to leave Channels 1 or 2 open for other inputs. You will have to control Tone and relative Level (between the Channels) at your input source, as you do not have this control over Channels 3 and 4 in the PS1 Power Stand (Classic) / Model I or the R1 Remote.
Outputs from the Mixer
¼ Inch with suitable output
for PS1 Powerstand Channel 1 or 2 inputs
You can use TS (Tip Sleeve) unbalanced cables, or TRS (Tip Ring Sleeve) balanced cables, but since the ¼ inch phone connections at the Bose Classic and Model I Power Stand are unbalanced there is no particular benefit using balanced cables.
¼ Inch Tip-Sleeve (unbalanced) to ¼ Inch Tip-Sleeve (unbalanced)
This should work fine.
¼ Inch Tip-Ring-Sleeve (balanced) to ¼ Inch Tip-Sleeve (unbalanced)
This should work fine.
¼ Inch Tip-Ring-Sleeve (balanced) to ¼ Inch Tip-Ring-Sleeve (balanced)
This should also work, but likely no better than a simple ¼ Inch Tip-Sleeve to Tip-Sleeve cable. This is because the ¼ Inch input on the Bose System is Tip-Sleeve (unbalanced) anyway.
XLR Balanced +4
The nominal output of the XLR Balanced Outputs is too high for the XLR inputs on the PS1 Power Stand Channels 1 and 2. If you want to use balanced cables from the Mixer to Channels 1/2 on the L1 Classic or L1 Model I you may need to use a Pad to lower the signal level from the mixer.
{{#Click:Pad|Image:Pad.jpg|Attenuation Pad}}
If you want to use XLR cables you may need to use a pad
Links