Bose S1 Pro Compared to Bose L1® Compact

From Bose Portable PA Encyclopedia
Jump to: navigation, search


FeatureBose S1 ProBose L1® Compact
  S1 Pro Tilt-Back.jpg height:280px
Horizontal dispersion 120 degrees 180 degrees
Vertical dispersion 50 degrees 40 degrees
Output 103 dB / 109 dB peak 106 dB / 112 dB peak
Audience Up to 50 people Up to 100 people
Speaker Array Three 2.25" (5.715 mm) high-excursion drivers mounted in a curved Articulated Array® Six 2.00" (51 mm) high-excursion drivers mounted in a curved Articulated Array® loudspeaker
Woofer One 6" (152 mm) low-frequency driver mounted behind the three driver in a curved Articulated Array® One 8" (203 mm) low-frequency driver mounted in a ported bass enclosure in the power stand
Frequency Response
  • 62 Hz – 17 kHz +/- 3dB
  • 65 Hz – 14 kHz +/- 3dB
  • 50 Hz - 16 Hz (-10 dB)
Crossover

600 Hz

400 Hz

Power to speakers Biamped 80 Watts RMS x 2, 160 Watts total Biamped 65 Watts RMS x 2, 130 Watts total
Weight
  • 6.5 kg (14.3 lbs) – Without Battery
  • 7.0 kg (15.5 lbs) – With Battery
Total system weight 13.4 kg (30.2 lb)
  • Power Stand: 11.2 kg (24.6 lb)
  • Extensions (each): 1.1 kg (2.3 lb)
Multiple orientations
  • Elevated Surface Position the S1 Pro on a surface. This projects sound clearly and evenly throughout the audience, and ensures that audience members enjoy the full frequency range of the system.
  • Tilt-Back For performances where your audience is close to you, tilt the S1 Pro onto its back edge. For best results, the performer should stand or sit to one side of the loudspeaker to avoid blocking sound from the audience.
  • Monitor To use the S1 Pro as a personal floor monitor, place it on the ground horizontally, in front of and pointing toward the performer. Tilt the loudspeaker onto its side edge.
  • Speaker Stand Place one or two S1 Pro systems on speaker stands (sold separately) for general-purpose sound reinforcement. Monitor
  • Table Top (no extensions)
  • Floor with both extensions
    (no speaker stand required)
  • Floor with one extension
Bluetooth input Yes: Channel 3
Supports Bluetooth 4.2
No
Reverb Yes No
ToneMatch® Presets Channel 1
  • Vocal Microphone
  • Acoustic Guitar
  • OFF (flat)

Channel 2

  • Vocal Microphone
  • Acoustic Guitar
  • OFF (flat)
Channel 1
  • Fixed: Microphone

Channel 2

  • Acoustic Guitar
  • Line Level (flat)
Battery Yes internal (optional) No
Connections

Channel 1:
XLR / 6 mm (1/4" Tip-Ring or Tip-Ring-Sleeve) balanced / unbalanced

Channel 2:
XLR / 6 mm (1/4" Tip-Ring or Tip-Ring-Sleeve) balanced / unbalanced

Channel 3:
3 mm (1/8" Tip-Ring-Sleeve) accepts stereo or mono input

Channel 1:
XLR balanced

Channel 2:

  • 6 mm (1/4" Tip-Ring or Tip-Ring-Sleeve) balanced / unbalanced
  • 3 mm (1/8" Tip-Ring-Sleeve) accepts stereo or mono input
  • Two RCA unbalanced phone plug
Tone Controls Channels 1 and 2
  • Bass / Treble

Channel 3

  • None
Channel 1
  • Bass / Treble

Channel 2

  • None
Crossover Frequency 600 Hz 400 Hz 4th order Butterworth
Line Out ¼ inch (6mm) jack: Nominal +4 dBu, Max +20 dBu


Note: Using a TS unbalanced cable will result in a drop in the audio level of -6dBu.

¼ inch (6mm) jack: Nominal +2.2 dBu, Max +20 dBu


Note: Using a TS unbalanced cable will result in a drop in the audio level of -6dBu.