Difference between revisions of "T1 ToneMatch® Audio Engine / Routing for Effects"
m |
m (ST moved page T1 ToneMatch® Audio Engine / Routing for Effects to T1 ToneMatch® Audio Engine / Routing for Effects) |
||
| (2 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
| + | <table><tr> | ||
| + | <td valign="top" width="250">__TOC__</td> | ||
| + | <td valign="top"> | ||
| + | This article addresses some interesting options you have for routing your signal through the T1® to process effects more than once. | ||
| + | |||
| + | For ideas on how you can work with an external effects unit see: [[T1 ToneMatch® Audio Engine / Insert for External Effects]] | ||
| + | |||
| + | </td> | ||
| + | </tr></table> | ||
| + | |||
There are several less than obvious things you can do with effects through the {{T1}}. | There are several less than obvious things you can do with effects through the {{T1}}. | ||
| − | + | === Parallel Effects === | |
| − | == Parallel Effects | ||
If you want to swap between two sets of effects or run two sets of effects at the same time (for example: two delays, two modulation effects, two reverbs) try this. | If you want to swap between two sets of effects or run two sets of effects at the same time (for example: two delays, two modulation effects, two reverbs) try this. | ||
| Line 15: | Line 24: | ||
**Channel 1 and Channel 2 in parallel<br> | **Channel 1 and Channel 2 in parallel<br> | ||
| − | == Serial Effects | + | === Serial Effects === |
| − | If you want to run some effects and then add more effects in series then take the output of one or more {{T1}} Channels to the Aux Output, then take the Aux Output and use that as the input to another T1® Channel | + | If you want to run some effects and then add more effects in series then take the output of one or more {{T1}} Channels to the Aux Output, then take the Aux Output and use that as the input to another T1® Channel |
Assume that you are using Channel 1 as the input where you want to do this:<br> | Assume that you are using Channel 1 as the input where you want to do this:<br> | ||
| Line 30: | Line 39: | ||
**Channel 1 and Channel 2 in series<br> | **Channel 1 and Channel 2 in series<br> | ||
| − | == Foot Switch to Mute Effects<br> == | + | === Foot Switch to Mute Effects<br> === |
From Andy-at-Bose UK<br> | From Andy-at-Bose UK<br> | ||
| Line 37: | Line 46: | ||
<br> | <br> | ||
| − | + | <noinclude> | |
<br> | <br> | ||
| − | This article is a stub. Please help us if you can by expanding it. | + | This article is a stub. Please help us if you can by expanding it. |
| − | |||
---- | ---- | ||
[[Category:T1]] | [[Category:T1]] | ||
[[Category:Effects]] | [[Category:Effects]] | ||
</noinclude> | </noinclude> | ||
Latest revision as of 04:54, 26 March 2017
|
This article addresses some interesting options you have for routing your signal through the T1® to process effects more than once. For ideas on how you can work with an external effects unit see: T1 ToneMatch® Audio Engine / Insert for External Effects |
There are several less than obvious things you can do with effects through the T1 ToneMatch Audio Engine.
Parallel Effects
If you want to swap between two sets of effects or run two sets of effects at the same time (for example: two delays, two modulation effects, two reverbs) try this.
Assume that you are using Channel 1 as the input where you want to do this:
- Set the effects you want on Channel 1
- Take a ¼ inch jack cable from the Channel 1 PreAmp Out to Channel 2 input
- Add the second layer of effects you want to Channel 2
- Now use the FX Mute buttons for Channels 1 and 2 to set which banks of effects will be used
- Channel 1 only
- Channel 2 only
- Channel 1 and Channel 2 in parallel
Serial Effects
If you want to run some effects and then add more effects in series then take the output of one or more T1 ToneMatch Audio Engine Channels to the Aux Output, then take the Aux Output and use that as the input to another T1® Channel
Assume that you are using Channel 1 as the input where you want to do this:
- Set the effects that you want on Channel 1
- Set the Aux tap to Pre
- Take a ¼ inch jack cable from the Aux Out to Channel 2 input
- Apply effects that you want applied to the output of Channel 1
- Now use the FX Mute buttons for Channels 1 and 2 to set which banks of effects will be used
- Channel 1 only
- Channel 2 only
- Channel 1 and Channel 2 in series
Foot Switch to Mute Effects
From Andy-at-Bose UK
First up hook up your vocal mic to, say, Channel 1 on the T1®. Next take a jack lead and connect it to the PRE AMP out on Channel 1. Take this lead and run it through either a keyboard style volume pedal or a make or break style footswitch. Run the signal from the pedal/footswitch into another T1® channel and set this channel up with the chosen vocal effects but make them 100% effect. Adjust the effected channel volume to get the desired blend of dry vocal to effected vocal. The pedal/footswitch will determine how much or if any signal will go to channel 2 and therefore whether or not an effect is added.
This article is a stub. Please help us if you can by expanding it.