Category:Mixer

From Bose Portable PA Encyclopedia
Revision as of 03:41, 11 December 2008 by ST (talk | contribs) (Mixer General Notes)
Jump to: navigation, search

Alesis MultiMix8USBBehringer UB1202Mackie 1202 VLZ ProNumark CD Mix-2Spirit NotepadYamaha MG82/FX



Mixers

Model I and Classic

XLR to XLR

The XLR inputs for Channels 1 and 2 are intended for microphone level inputs.

  • If your source (mixer or CD/DVD player) has XLR outputs, check to see if you have the option to set it to a microphone level output. If so, use that setting.
  • If your source has XLR outputs at line-level (most likely) then you will probably need a Pad between the source and the Model I nl (or Classic nl) Power Stand.
  • You may be able to make things work without the Pad by turning down the output from the source and turning down the trim at the Power Stand. If it sounds okay then you are probably fine. If you cannot get enough a good sounding signal without an excess of noise then try a Pad.
¼ inch jack inch to ¼ inch

If your mixer has ¼ inch jack outputs, these are almost certainly at line-level and should work well with any of the ¼ inch jack inputs (Channels 1, 2, 3, 4) on a L1 Model I or L1 Classic.

L1 Model II

A ¼ inch Tip-Ring-Sleeve connector carrying a stereo signal should not be used with the analog input on the Model II.

Even though a ¼ inch Tip-Ring-Sleeve connector can carry a stereo signal this is not how this physical connection is used on the Mixer Power Stand.

The analog input on the Model II is balanced, and will therefore subtract the Left and Right signals on a stereo cable and you will hear an L-R (Left minus Right) signal in the Model II.

You cannot 'get through the gig' this way if you are a DJ or if you need to run prerecorded music or have stereo inputs.

TRSfromStereoRCAModelII.png

TRSfromStereo14ModelII.png

18stereoTo14stereoModelII.png


Using a Mixer

L1 Model II

Alesis MultiMix8USBBehringer UB1202Mackie 1202 VLZ ProNumark CD Mix-2Spirit NotepadYamaha MG82/FX

If you are using a mixer instead of a T1 ToneMatch Audio Engine use the mixer to create a mono output and send that to the Model II Power Stand Analog input.

  • If there is a stereo/mono switch then use it and send the mono output to the Model II Power Stand Analog input.
  • If there is a Left/mono output then use that and send it to the Model II Power Stand Analog input.
  • If there is no way to create a mono output then pan all your mixer inputs all the way to one side (e.g. Left) and then take the mixer for that side (e.g. Left) output and send it to the Model II Power Stand Analog input.



T1 ToneMatch Audio Engine

You can probably run XLR or ¼ inch jack line level inputs to the T1® Channels 1,2,3. If you have the option to run ¼ inch to ¼ inch, you could use T1® Channels 4/5.


Subcategories

This category has the following 8 subcategories, out of 8 total.

A

B

G

M

N

S

Y

Pages in category "Mixer"

The following 105 pages are in this category, out of 105 total.

A

B

C

D

G

L

M

P

S

T

Y

Media in category "Mixer"

The following 97 files are in this category, out of 97 total.

Retrieved from "https://toonz.ca/bose/wiki/index.php?title=Category:Mixer&oldid=9513"