Search results
Create the page "S" on this wiki! See also the search results found.
- * On the {{S1}}s set the gain staging with the source device * Connect the F1 Subwoofer outputs 1 and 2 to the {{S1}}s2 KB (306 words) - 21:25, 16 November 2019
- ...It's fairly big, measuring 382mm (15 inches) across its lower bouts and it's deeper, too, with the rim measuring 60.6mm (2.39 inches). In terms of overa ...lly designed with jazz musicians in mind. But with several innovations, it's no surprise rockers are loving it too. Highlights include a "pattern" neck13 KB (1,896 words) - 10:13, 27 July 2022
- <strong class="text-strong">Here's what we know</strong><br> ...e G10T is plugged into the amp, the switch is depressed (just like when it's plugged into a guitar). <br>3 KB (527 words) - 15:39, 19 February 2021
- ...the receiver’s display. If there is an RF signal showing on the receiver's display when the transmitter is off, that indicates that the receiver is pi Once a new frequency is selected, get back to the receiver's main display. If there is no RF registering, then this new frequency is a "6 KB (1,141 words) - 11:48, 8 April 2021
- Connect the output(s) of a line-level source (e.g. Helix line-level outputs) to the line-level i Set the Helix XLR output(s) to Line level if using an XLR to 1/4 inch (6.3 mm) Tip-Ring-Sleeve cable.3 KB (516 words) - 00:51, 5 January 2023
- Connect the output(s) of a line-level source (e.g., on the Kemper the line-level outputs are XLR Set the Helix XLR output(s) to Line level if using an XLR to 1/4 inch (6.3 mm) Tip-Ring-Sleeve cable.5 KB (706 words) - 00:49, 5 January 2023
- * There's no reason to just tap with just the toe or ball of your foot. You can also ...Board, but the associated distortion can ''(judiciously applied)'' have it's own place. Besides, why should guitarists be the only ones who have fun wi14 KB (2,228 words) - 15:42, 12 September 2024
- ...f you have more than one performer. With more than one performer/source it's in my opinion always preferable to separate the sources (i.e. one source pe ...One will be more accurate (i.e. sound is clearly located at the performer's position, more consistent spectrum) and two will sound wider and more spaci3 KB (450 words) - 10:26, 22 September 2024
- Please note: The {{L1 CR}}s (pictured at the top of this page) from the {{Model I}} and {{Classic}} are ...tolerances. One L1 is virtually indistinguishable from the next one, so it's perfectly ok two swap speaker and power stands.12 KB (2,008 words) - 05:55, 26 March 2017
- ...tage in terms of feedback. An omnidirectional mic collects more sound that's not the target, and because it has no proximity effect is more susceptible ...u're using either of these polar patterns on stage with wedge monitors, it's important make sure you avoid placing the wedges directly behind the mic in16 KB (2,433 words) - 19:03, 1 July 2023
- ...es. Other generous rooms are available to us for breakout sessions if that's what we decide to do. * There's also cabins that sleep eight people each in twin beds (no bunks). Beds are4 KB (735 words) - 17:33, 26 March 2017
- ...le from the L1™s, try adding direct boxes between the mixer and the L1™s. ...line to line direct box. If the two channels are used on two separate L1™s put the two channel direct box close to the mixer. Alternately, have your8 KB (1,303 words) - 08:31, 7 April 2019
- Here is Mike's first mention of Presets 3.0 - August 16, 2007 There are 3 breeds of L1's in the field:3 KB (399 words) - 14:30, 10 December 2019
- ...for the Cylindrical Radiators® depending on the presence/absence of {{B1}}s attached to the Bass Module output. This is due to the design change (Cylin ...ew of why this is a good design goal (of which you may disagree) but let’s look at the actual behavior first.5 KB (854 words) - 04:26, 26 March 2017
- ...s an odd-brand "installed" system), all bets are off. Actually, even if it's a really good installed system but all the controls (like the house EQ) are :Bring the T1 though - worst case scenario is you leave your EQ's flat.3 KB (421 words) - 14:49, 8 June 2021
- ...a high percentage of T1 owners did not know about the BYPASS feature that's employed in many places in the T1. ...n deciding if a particular adjustment is giving you the sound you want. It's a form of an A/B switch.2 KB (376 words) - 20:57, 14 November 2023
- ...h® Audio Engine power supply]] (required unless one of your {{L1 no link}}s is a {{Model II}}). Make the following connections. If you are running two {{Classic}}s or {{Model I}} or {{Compact}} Systems, then you will also need the optional7 KB (1,115 words) - 15:44, 4 September 2023
- === What about using just the lower half of an {{L1}} system's loudspeaker in places where the ceiling isn't tall enough for full assembly5 KB (774 words) - 15:10, 28 April 2023
- :Well, it's official. We've started work on a gig bag for the B1, based on your valuabl ...ad, they are really a nice "slip cover" to go over your B1 Bass Module. It's constructed so the same beefy handle can be used to carry the product, now21 KB (2,953 words) - 17:18, 16 October 2022
- ...se a computer network cable type CAT5 or CAT6 or CAT7 or CAT8 cable. There's no compelling reason to choose higher category cables. All should work. ...few hundred uses you may notice the occasional drop out, at which point it's time to get a new one.5 KB (805 words) - 18:12, 6 June 2021